Metal Die Casting Lubricants

Metal Die Casting Lubricants

metal die casting lubricants ● Type of product DY05(34#),DY8(39#)DY07c(140#C) DY05 (34#)is grey color with paste, strong adhesion, good heat resistance function, duration and suitable for processing z fine thin section, ● Product application DY05 (34#)is grey color with paste, strong adhesion,...

Details

metal die casting lubricants

 

Type of product

DY05(34#),DY8(39#)DY07c(140#C)

DY05 (34#)is grey color with paste, strong adhesion, good heat resistance function, duration and suitable for processing z fine thin section,

Product application

DY05 (34#)is grey color with paste, strong adhesion, good heat resistance function, duration and suitable for processing z fine thin section,too flat surface cast and spraying cap open system

DY08(39#) is white color, fine particle, good heat resistance, strong adhesion and very good for base

DY07C(140#C) combines the feature between DY05 (34#)and DYO8 (39#) and uses it alone so as to obtain good effect and also

spreading cap open part to reach good function for making up shrinkage.

Feature for product

1, Reducing cast stripping resistance to prevent it from adhesion and easy stripping

2. Improvement for cast surface quality and cleanness and brightness;

3. Metal liquid may flowing to facilitate cast frozen and cool metal speed

4. Protect mould type and cavity and reduce corrosion to extend it life

5, Feature for exhausting air function

Storage for product

1.Keep it in cool place and better put at 10c-13'c and storage period is 6 months

2. Package for product 5 kg/bucket and 20 kg/box

Instruction for use

1. DY05(34#)and DY08 (39#)stripping agent (coating) are two types of low case stripping (coating) to be combined to be use with best effect

2. DY 07C (140#C) metal type casting stripping agent (agent) is one stripping agent (costing) made for casting motorcycle wheel hub.


Three coatings are used as follows for reference

Operation

procedure

DY05(34#

stripping Agent

DY0839#stripping Agent

DY07C140#C

stripping Agent

Requirement for operation

Mould clean

Mould must be treated for blasting sand before spraying coasting to remove rust,dirt substance and remaining costing on the mould surface The blasting sand uses manual sand sprayer and sand or glass Bead.

1.Before,mould is used, must stir it evenly(because long time place, it with heavy gravity is go down base.

2.Before spraying, must clean old

coating on the mould

3. The mould temperature is lower than

170oc. It doesn't need spraying

coating

4. don't spray too thick 0.07-0 2 mm

coating layer in normal

5. The pressure used in spraying

compressed air less than 30PSI and

spraying coating for mist

6. Spraying should be moved in different

directions rapidly.

7. The stripping agent is alkaline to

stimulate skin and certain metal to

avoid direct touch by hand. Don’t

splash on the skin and clothes. If it

happens like that, the skin and clothes

must be cleaned with clean water

rinsing. Put on protection glass when

spraying

 

Mould spraying temperature

Clean mould, pre-heating to 260 to 320, and then clean mould surface dirt substance, dust and adjust temperature to 210C to 250o and then for coating.

Compounding stripping agent

Stir stripping agent in the tank first and take out agent required to be stirred evenly up to the proportion of dilution, pass sieve( diameter 0. 55), put in the spray gun and should stir it evenly before use it.

Proportion

of dilution

13-4

1:2-3

1:4-6

Selection for spray gun

Adjust compressed air pressure(pressure not exceeding 30PSI) and spray jet first to make jet with mist. When spraying coasting, the jet keeps away from surface with 220 350 mm. If too far or near, it affects the quality for costing to cause spot or stack; When spraying coating, coating layer for 4-5 layers instead or 1-2 layers to obtain perfect coating. The operator should spray from different direction and move the gun continuously to reduce large area Coating Shade(Coating Lack caused by bulge table cover strongly

Making up for cycle

Making up for spraying for each 4-5 hour with amount 1 -2 layers thin layer. In general, making up DY05 (34#) stripping agent and DY 07C (140#) stripping agent

Cycle

continuing working 9 12 shifts shall need stop cleaning spraying sand in normal and spraying stripping agent again.

 

 

 

Hot Tags: metal die casting lubricants, Asia, China, suppliers, manufacturers, factory, wholesale, made in China

Feedback

Subscribe to our email list
Sign up with your name and email to get the latest proway updates, exclusive access to promotions, sales events, pre-order sales & more!
Connect with Rolitone
Become our fan, follow us & subscribe for the latest updates and deals
QR Code
  • About Us
  • Products
  • RLT Lab
  • Knowledge
  • Contact Us
  • Feedback
  • Case
  • Catalog
  • Copyright © Rolitone technology Co.,Ltd. All Rights Reserved.